09/2008 awt6314r dual-band cdma/pcs 3.4 v/28 dbm linear power amplifer module data sheet - rev 2.0 m23 package 12 pin 3 mm x 5 mm x 1 mm surface mount module features ? single mode operation: p out ? +28 dbm ? high effciency: 39 % ? 25 % package size reduction ? common v mode control line ? simplifed v cc bus pcb routing ? reduced external component count ? low profle surface mount package: 1.1 mm ? rohs compliant package, 250 o c msl-3 applications ? cdma/evdo cell & pcs dual-band wireless handouts and data devices product description the awt6314r meets the increasing demands for higher levels of integration in dual-band cdma/pcs 1x handsets, while reducing board area requirements by 25 %. the package pinout was chosen to enable handset manufacturers to easily route v cc to both power amplifers and simplify control with a common v mode pin. the device is manufactured on an advanced ingap hbt mmic technology offering state-of-the-art reliability, temperature stability, and ruggedness. selectable bias modes that optimize effciency for different output power levels, and a shutdown mode with low leakage current, serve to increase handset talk and standby time. the self contained 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, effciency and linearity in a 50 ? system. figure 1: block diagram aw t6314 bias control v ref_pcs v mode rf in_pcs gnd v cc2 a v cc1 1 11 9 12 10 3 4 2 rf out_pcs v cc2 5 6 8 7 bias control rf out_cell gnd v ref_cell rf in_cell gn da t slug (pad) gnd
2 data sheet - rev 2.0 09/2008 at631 table 1: pin esription table fire 2: pinot v ref_pcs rf out_pcs rf in_pcs v mode gnd 1 gnd 12 2 3 4 5 8 11 10 9 v cc2 gnd gnd 6 7 v cc1 rf in_cell v ref_cell rf out_cell v cc2 a pin nam dscripin 1 v ref_pcs reference voltage for pcs band 2 rf in_p c s rf input for pcs band 3 v cc1 supply voltage 4 v mode mode control voltage 5 rf in_cell rf input for cell band 6 v ref_cell reference voltage for cell band 7 gnd ground 8 rf out_cell rf output for cell band 9 v cc2 a supply voltage 10 v cc2 supply voltage 11 gnd ground 12 rf out_pcs rf output for pcs band
data sheet - rev 2.0 09/2008 awt6314r 3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. table 3: operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. notes: (1) for operation at v cc = +3.2 v, p out is derated by 0.5 db. parameter min max unit supply voltage (v with rf drive dc only +5 mode control voltage (v mode +3.5 reference voltage (v ref +3.5 rf input power (p +10 storage temperature (t stg +150 parameter min typ max unit comments operating frequency (f) 1850 849 1910 mhz supply voltage (v reference voltage (v ref +2.75 +2.85 +3.1 +0.5 mode control voltage (v mode +2.5 +2.85 +3.1 +0.5 high bias mode rf output power (p out 30.5 (1) 27.5 (1) 31.0 case temperature (t +85
4 data sheet - rev 2.0 09/2008 at631 table 4: electrical specifcations - cellular cdma operation ? notes: (1) pae and acp limit applies at 836.5 mhz. paamete mn tp ma unt comment gain 25 24 23.5 27.0 26.5 25.5 30 29 28 db p o u t = +28 dbm, v m o d e = 0 v p o u t = +28 dbm, v m o d e = +2.85 v p o u t = +16 dbm, v m o d e = +2.85 v adjacent channel power at 885 khz offset (1) primary channel bw = 1.23 mhz adjacent channel bw = 30 kh - - - -50 -50 -49 -47 -47 -47 dbc p o u t = +28 dbm, v m o d e = 0 v p o u t = +28 dbm, v m o d e = +2.85 v p o u t = +16 dbm, v m o d e = +2.85 v adjacent channel power at 1.98 mhz offset (1) primary channel bw = 1.23 mhz adjacent channel bw = 30 khz - - - -62 -60 -65 -57 -57 -57 dbc p o u t = +28 dbm, v m o d e = 0 v p o u t = +28 dbm, v m o d e = +2.85 v p o u t = +16 dbm, v m o d e = +2.85 v power-added efficiency (1) 37 37 8 39 40 9 - - - % p o u t = +28 dbm, v m o d e = 0 v p o u t = +28 dbm, v m o d e = +2.85 v p o u t = +16 dbm, v m o d e = +2.85 v quiescent current (icq) - 50 68 ma v m o d e = +2.85 v, low bias reference current - 1.5 3 ma through v r e f pin, pa "on" mode control current - 0.6 1.0 ma through v m o d e pin, v m o d e = +2.85 v leakage current - <1 5 b a v c c = +4.3 v, v r e f = 0 v, v m o d e = 0 v noise in receive band - -133 -131 dbm/hz 869 mhz to 894 mhz harmonics 2fo 3fo, 4fo - - -44 -46 -30 -30 dbc input impedance - - 2:1 vswr spurious output level (all spurious outputs) - - -65 dbc p o u t < +28 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating conditions load mismatch stress with no permanent degradation or failure 10:1 - - vswr applies over all operating conditions
data sheet - rev 2.0 09/2008 awt6314r 5 table 5: pcs electrical specifcations (t c = +25 c, v cc = +3.4 v, v ref = +2.85 v, 50 ? system) notes: (1) acprs and effciency limits at mid-band only. parameter min typ max unit comments gain 24.5 26.5 26.0 25.5 29 27.5 out = +28 dbm, v mode out = +28 dbm, v mode = +2.85 v out = +16 dbm, v mode = +2.85 v adjacent channel power 1.25 mhz offset primary channel bw - 1.23 mhz adjacent channel bw = 30 khz -49 -50 -54 -46.5 dbc out = +28 dbm, v mode out = +28 dbm, v mode = +2.85 v out = +16 dbm, v mode = +2.85 v adjacent channel power 2.25 mhz offset primary channel bw - 1.23 mhz adjacent channel bw = 30 khz -62 -61 -67 -57 -57 -57 dbc out = +28 dbm, v mode out = +28 dbm, v mode = +2.85 v out = +16 dbm, v mode = +2.85 v power-added efficiency 36 36 7.5 39 9 % out = +28 dbm, v mode out = +28 dbm, v mode = +2.85 v out = +16 dbm, v mode = +2.85 v quiescent current (icq) 53 mode = +2.85 v reference current through v ref pin, pa "on" 0.6 1.0 through v mode pin, v mode = +2.85 v leakage current <1 5 = +4.3 v, v ref = 0 v, mode noise in receive band -133 -131 dbm/hz 1930 mhz to 1990 mhz harmonics 2fo 3fo, 4fo -55 dbc input impedance 2:1 vswr spurious output level -65 dbc out in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 vswr applies over full operating range
6 data sheet - rev 2.0 09/2008 awt6314r application information to ensure proper performance, refer to all related application notes on the anadigics web site: http://www.anadigics.com shutdown mode the power amplifer may be placed in a shutdown mode by applying a logic low levels (see operating ranges table) to both the v ref mode voltages. table 6: bias control bias modes the power amplifer may be placed in either a low bias mode or a high bias mode by applying the appropriate logic level (see operating ranges table) to the v mode voltage. the bias control table lists the recommended modes of operation for various applications. figure 3: application circuit application p out levels bias mode v ref v mode cdma all power 28 dbm low +2.85 v +2.85 v high +2.85 v rf in_cell 1 11 9 12 10 5 6 rf in_pcs slug mode cc1 ref_cell ref_pcs 1000 pf 15 pf 3.9 nh 68 pf 1000 pf 0.01 ?f ?f ?f 0.01 ?f trl 1 note: 1. 3.9 nh inductor should be rated for >1 amp.
data sheet - rev 2.0 09/2008 awt6314r package outline figure 4: package outline - 12 pin 3 mm x 5 mm x 1 mm surface mount module figure 5: branding specifcation 6314r yyww lllll 6. w ork w eek r, ww = wo rk w eek
warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. important notice anadigics, inc. 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com e-mail: mktg@anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.0 09/2008 8 awt6314r ordering information order number temperature range package description component packaging awt6314rm23q7 -30 c to +85 c rohs compliant 12 pin 3 mm x 5 mm x 1 mm surface mount module tape and reel, 2500 pieces per reel AWT6314RM23P9 -30 c to +85 c rohs compliant 12 pin 3 mm x 5 mm x 1 mm surface mount module partial tape and reel
|
